PRIMUS FS 6-16 INSTALLATION AND MAINTENANCE MANUAL Pdf Download | ManualsLib

Part numbers:

Nr.

part number

525927 (H616)

525928 (H956)

525921 (H323)

311902100008

PRI202000090

310934000008

525928 Instruction AC-reactor FS16-55 RS27-35

description

SERVICE KIT COMPLETE

This service instruction

FR-BAL-B-7,5k Power factor reactor

Washer M8

Screw M8x16

Nut M8

Quantity

P3/15

1. ERROR HANDLING

The timer allows the full control of the washing machine. When an error occurs then automatically the

machine will go over to a safe state. With the diagnostic program you can determine the problem ( See

Program manual). This program will test all the functions of the washing machine.

If a failure occurs then the computer will display a diagnostic message. The message is a number that

correspond with a typical problem.

If a failure occurs and the timer gives no message you can consult chapter 6.2.

2. PROBLEM CHECK LIST

Problem

When the power is switched on :

the display is not lighting up

Remark :

The display must always light up

when the power connector is

connected to the power board

(EPROM with software must be

implemented)

The machine is not starting up when

the start button is pressed.

Coins are inserted but the displayed

program price is not counting down

Coindrop is accepting coins but does

not start the washer

The machine is not responding on

pressing the keyboard buttons

The dot to indicate that the software is

in program mode can not be enabled

100 646 PUB.DATE : 05/02

Cause

• no external power

• the emergency button is activated

• the power connector is not

connected on the board

• the power connector is inverse

connected

• the fuse on the PWR board has

jumped

• the input connector is disconnected

• the EPROM that contains the

software is not implemented

• the key switch stands in Program

mode

• the correct amount of coins is not

inserted

• the door is not closed properly

• the micro contact mounted on the

coin drop is not functional

• the optocoupler mounted on the

coindrop is not functional

• check the wiring to the coindrop

• verify if you have entered a coin

value in the u-submenu for the

corresponding coindrop

• the start button is not pushed after

the amount is flashing on ’00’

• the right amount is not reached

• the door is not closed properly

• the key switch is not functional (no

dot is displayed when switching in

Program mode)

• the START button is not functional

(the key switch stands in Program

mode)

• the SET button is not functional (the

key switch stands in Run mode)

• no button is functional and the key

switch is in the right position

• the key switch is not functional

INSTALLATION AND MAINTENANCE MANUAL

Solving the problem

• verify the external tension of the

machine

• deactivate the emergency button

• connect the power connector

• check the wiring and connect the

connector as it must be

• if the transformer is deformed replace

the PWR board

Check the wiring and the tension at the

power Connector

If the transformer is still OK change the

Fuse

• if the display is lighting up: verify that

the input signals or the 16 V signal are

not touching the cabinet

• put the right EPROM with software into

the socket on the board.

• set the Key switch to Run mode

• the start button must be pressed when

00 is flashing on the lower display

• close the door

• verify the well functioning of the micro

contact of the coindrop :

positive pulses should be generated

• verify the well functioning of the

optocoupler positive pulses should be

generated

• if the wiring is broken: repair the wiring

• insert the correct coin value in the u-

submenu

• push the start button

•Put the right amount in the coindrop

• close the door

• check if the input connector A is well

connected and check the wiring between

the input connector and the keyswitch

• set the Key switch to Run mode

• set the Key switch to Program mode

• check if the connector K of the keyboard

is well connected

• check if the input connector A is well

connected and check the wiring between

Electrical details:

………….VOLT……………PHASE…………HZ

NOTE:

ANY CONTACTS WITH YOUR DEALER REGARDING

MACHINE SAFETY, OR SPARE PARTS, MUST INCLUDE

THE ABOVE IDENTIFICATION.

MAKE CERTAIN TO KEEP THIS MANUAL IN A SECURE

PLACE FOR FUTURE REFERENCE.

DEALER:

Summary of contents for primus fs16

Информация для государственных заказчиков

Цены на оборудование, указанные в прайс-листе, носят исключительно информационный характер и не являются публичной офертой, в связи с чем не могут быть использованы для обоснования начальной или максимальной цены государственного контракта (приказ №567 от 02.03.2021 п.: 3.10, 3.16, 3.17).

Прайс-листы и цены

Прайс-лист Вязьма 2021 ⋅ Прайс-лист мини-прачечные 2021 ⋅ Каталог Вязьмa 2021

Промышленная сушильная машина primus t16 | «фабрика-кухня»

Промышленная сушильная машина primus t16 цена и характеристики

Сушильные машины для прачечной

Модель: T16
Загрузка номинальная: 16 кг
Мощность нагрева: 24 кВт
Нагрев: Электрический
Напряжение: 380 В
Объём барабана: 345 л
Тип сушки: Вентиляционная
Цена: 388 000 ₽

Модель: T13
Загрузка номинальная: 13 кг
Мощность нагрева: 18 кВт
Нагрев: Электрический
Напряжение: 380 В
Объём барабана: 285 л
Тип сушки: Вентиляционная
Цена: 372 000 ₽

Модель: T24
Загрузка номинальная: 24 кг
Мощность нагрева: 30 кВт
Нагрев: Электрический
Напряжение: 380 В
Объём барабана: 530 л
Тип сушки: Вентиляционная
Цена: 434 000 ₽

Дополнительно:  Почему сушильная машина течет : причины | Мастер-Быт24

Модель: T11
Загрузка номинальная: 11 кг
Мощность нагрева: 13.5 кВт
Нагрев: Электрический
Напряжение: 380 В
Объём барабана: 250 л
Тип сушки: Вентиляционная
Цена: 332 000 ₽

Модель: T35
Загрузка номинальная: 35 кг
Мощность нагрева: 36 кВт
Нагрев: Электрический
Напряжение: 380 В
Объём барабана: 680 л
Тип сушки: Вентиляционная
Цена: 629 000 ₽

Купить сушилка барабанная primus lavamac t16 / ls 350, прачечная: отзывы, фото и характеристики на